This guide applies to all break barrel rifles, including Sniper models, TPR models, and the 1200G. ⚠️ Important: Always ensure your rifle is unloaded and degassed before performing any cleaning or maintenance. Cleaning. Barrel Cleaning. Most of our b

This guide applies to all break barrel rifles, including Sniper models, TPR models, and the 1200G.&#xA0;&#x26A0;&#xFE0F; Important: Always ensure your rifle is unloaded and degassed before performing any cleaning or maintenance.Cleaning<ul data-start="354" data-end="633"><li style="line-height: 1; font-size: 12px;">Wipe all exterior surfaces with a dry microfiber cloth.</li><li style="font-size: 12px;">Lightly lubricate exposed steel parts (barrel, compression tube, cocking linkage) with a firearm protectant such as Ballistol, RemOil, or CLP.<ul style="font-size: initial;"><li style="line-height: 1; font-size: 12px;">Avoid plastic surfaces.</li><li style="line-height: 1; font-size: 12px;">Always wipe away excess oil.</li></ul></li></ul>Barrel CleaningMost of our break barrels have a non-removable silencer, so we recommend using felt cleaning pellets.<ol data-start="770" data-end="952"><li style="line-height: 1; font-size: 12px;">Cock the gun.</li><li style="line-height: 1; font-size: 12px;">Load one felt cleaning pellet (in the correct caliber).</li><li style="line-height: 1; font-size: 12px;">Load a lead pellet behind it.</li><li style="line-height: 1; font-size: 12px;">Fire the combination.</li><li style="line-height: 1; font-size: 12px;">Repeat a few times until clean.</li></ol>&#x25B6;&#xFE0F; <a data-start="957" data-end="1051" rel="noopener" target="_new" href="https://www.youtube.com/watch?v=a3QatVu8OnY&amp;feature=youtu.be&amp;utm_source=chatgpt.com">Watch this video demonstration</a>Lubrication<ul data-start="1078" data-end="1353"><li style="line-height: 1; font-size: 12px;">Apply one drop of Ballistol, RemOil, or CLP to each cocking linkage pivot point every 500&#x2013;1000 shots.</li><li style="line-height: 1; font-size: 12px;">Wipe up excess oil, or spread it across the linkage to protect metal surfaces.</li><li style="line-height: 1; font-size: 12px;">While lubricating, check that stock screws and optic screws are tight.</li></ul>Piston Lubrication (Important)<ul data-start="1397" data-end="1692"><li style="line-height: 1; font-size: 12px;">The piston is factory-lubricated for the lifespan of the gun.</li><li style="line-height: 1; font-size: 12px;">Never apply oil down the transfer port.</li><li style="font-size: 12px;">If the gun makes a &#x201C;honking&#x201D; noise:<ul style="font-size: initial;"><li style="line-height: 1; font-size: 12px;">Under warranty: The rifle will need replacement.</li><li style="line-height: 1; font-size: 12px;">Out of warranty: You may attempt the following at your own risk:</li></ul></li></ul>Honk Fix Procedure<ol data-start="1719" data-end="2061"><li data-start="1719" data-end="1752" style="line-height: 1; font-size: 12px;">Confirm the gun is unloaded.</li><li data-start="1753" data-end="1775" style="line-height: 1; font-size: 12px;">Remove the stock.</li><li data-start="1776" data-end="1836" style="line-height: 1; font-size: 12px;">Secure the rifle with the barrel pointing downward.</li><li data-start="1837" data-end="1949" style="line-height: 1; font-size: 12px;">Apply 2&#x2013;3 drops of oil (motor oil is acceptable) to the piston body where the cocking linkage attaches.</li><li data-start="1950" data-end="1999" style="line-height: 1; font-size: 12px;">Let the gun rest in this position overnight.</li><li data-start="2000" data-end="2061" style="line-height: 1; font-size: 12px;">Reassemble and fire several test shots (never dry fire).</li></ol><hr data-start="2063" data-end="2066" style="line-height: 1;">

Break Barrel Cleaning & Lubrication Guide

⚠️ Important: Always ensure your rifle is unloaded and degassed before performing any cleaning or maintenance. Cleaning. Lubrication. Battery Care

&#x26A0;&#xFE0F; Important: Always ensure your rifle is unloaded and degassed before performing any cleaning or maintenance.Cleaning<ul data-start="221" data-end="675"><li style="line-height: 1; font-size: 12px;">Wipe all exterior surfaces with a dry microfiber cloth.</li><li style="line-height: 1; font-size: 12px;">To clean the barrel, watch this video: &#x25B6;&#xFE0F; <a data-start="329" data-end="405" rel="noopener" target="_new" href="https://www.youtube.com/watch?v=jszOjx0Z3Uo&amp;utm_source=chatgpt.com">How to Clean Your 400e Barrel</a></li><li style="font-size: 12px;">Barrel cleaning does not need to be performed often. For best results:<ul style="font-size: initial;"><li style="line-height: 1; font-size: 12px;">Clean the barrel once when you first get the gun.</li><li style="line-height: 1; font-size: 12px;">Never reuse ammo.</li><li style="line-height: 1; font-size: 12px;">Do not add lubricants to BBs or your speed loader.</li><li style="line-height: 1; font-size: 12px;">Clean only if you notice accuracy issues</li></ul></li></ul>Lubrication<ul data-start="699" data-end="1204"><li style="line-height: 1; font-size: 12px;">Apply a small amount of firearm lubricant to the magazine release mechanism. Wipe away excess.</li><li style="font-size: 12px;">The gearbox is factory-greased and will stay lubricated until it requires a rebuild.<ul style="font-size: initial;"><li style="line-height: 1; font-size: 12px;">Rebuilds can be done by an airsoft technician.</li><li style="line-height: 1; font-size: 12px;">Replacement parts and complete gearboxes are available on our website.</li></ul></li><li style="line-height: 1; font-size: 12px;">Do not lubricate inside the inner barrel or the bucking.</li><li style="line-height: 1; font-size: 12px;">You may lightly lubricate the exterior of the inner barrel with firearm lubricant. Always wipe away extra.</li></ul>Battery Care<ul data-start="1229" data-end="1740"><li data-start="1229" data-end="1285" style="line-height: 1; font-size: 12px;">Never overcharge or over-discharge your battery.</li><li data-start="1286" data-end="1351" style="line-height: 1; font-size: 12px;">Do not store your battery fully charged or deeply discharged.</li><li data-start="1352" data-end="1442" style="line-height: 1; font-size: 12px;">If the battery becomes puffy or swollen, discontinue use and dispose of it safely.</li><li data-start="1443" data-end="1488" style="line-height: 1; font-size: 12px;">Always charge with a balance charger.</li><li data-start="1489" data-end="1547" style="line-height: 1; font-size: 12px;">Use a voltage alarm for easier battery management.</li><li data-start="1548" data-end="1619" style="line-height: 1; font-size: 12px;">Be mindful of the risks of LiPo batteries and handle with care.</li><li data-start="1620" data-end="1673" style="line-height: 1; font-size: 12px;">Never store your gun with the battery inside.</li><li data-start="1674" data-end="1740" style="line-height: 1; font-size: 12px;">Disconnect any voltage alarms from the battery during storage.</li></ul>

400e Cleaning, Lubrication & Battery Care

⚠️ Important: Always ensure your rifle is unloaded and degassed before performing any cleaning or maintenance. Cleaning. Lubrication. Steel Air Tubes. Side Lever Actions. Traditional Bolt Actions. Long-Term Storage. Notes on Lubricants. Storage

&#x26A0;&#xFE0F; Important: Always ensure your rifle is unloaded and degassed before performing any cleaning or maintenance.Cleaning<ul data-start="349" data-end="1130"><li style="line-height: 1;">Wipe the exterior surfaces with a dry microfiber cloth.</li><li>To clean the barrel:<ul><li style="line-height: 1;">Use a patch puller or a soft metal cleaning rod (brass or aluminum).</li><li style="line-height: 1;">Run patches sized for your rifle&#x2019;s caliber through the barrel.</li><li>For very dirty barrels, moisten a patch with Ballistol.<ul><li style="line-height: 1;">If using another solution, confirm it is compatible with o-rings.</li></ul></li><li style="line-height: 1;">Follow with dry patches.</li><li style="line-height: 1;">Avoid using brushes.</li><li style="line-height: 1;">Be careful in the breech area &#x2014; patches that are too thick can dislodge the breech o-ring.</li></ul></li><li>Clean the barrel:<ul><li style="line-height: 1;">Once when you first receive the rifle.</li><li style="line-height: 1;">Any time you notice accuracy issues.</li></ul></li><li style="line-height: 1;">Maintain your filling equipment to ensure clean, dry air is entering your rifle. Reference your filling equipment&#x2019;s manual.</li></ul>LubricationSteel Air Tubes<ul data-start="1177" data-end="1431"><li style="line-height: 1;">Apply a thin protective film of firearm lubricant on the exterior surface.</li><li style="line-height: 1;">Do this if exposed to moisture, cold, or about every 500 rounds.</li><li style="line-height: 1;">For best results, remove the action from the stock to coat all surfaces.</li><li style="line-height: 1;">Wipe away excess.</li></ul>Side Lever Actions<ul data-start="1458" data-end="1575"><li>Apply a drop of firearm lubricant to:<ul><li style="line-height: 1;">Pivot points</li><li style="line-height: 1;">Bolt body</li></ul></li><li style="line-height: 1;">Use sparingly and wipe up any extra.</li></ul>Traditional Bolt Actions<ul data-start="1608" data-end="1780"><li style="line-height: 1;">Cock the bolt.</li><li style="line-height: 1;">Apply a thin film of white lithium grease to exposed surfaces.</li><li style="line-height: 1;">Work the bolt forward and back several times to spread.</li><li style="line-height: 1;">Wipe up any extra.</li></ul>Long-Term Storage<ul data-start="1806" data-end="1936"><li style="line-height: 1;">Run a patch moistened with Ballistol through the barrel.</li><li style="line-height: 1;">Before resuming use, run a couple of dry patches to clear it.</li></ul>Notes on Lubricants<ul data-start="1969" data-end="2374"><li style="line-height: 1;">Use 100% pure silicone oil or grease only for high-pressure air components (valve or regulator o-rings, etc.).</li><li style="line-height: 1;">Do not use firearm lubricants (including Ballistol) on o-rings, valves, or regulators.</li><li style="line-height: 1;">Avoid using spray lubricants, even if silicone-based.</li><li style="line-height: 1;">If your rifle uses a fill probe, apply a very light amount of silicone oil or grease to the o-rings and wipe away the excess.</li></ul>Storage<ul data-start="2395" data-end="2485"><li data-start="2395" data-end="2485" style="line-height: 1;">If storing safely away from unauthorized users, leave 1000&#x2013;1500 psi in your rifle.</li></ul>

PCP Rifle Cleaning & Maintenance

⚠️ Always ensure the rifle is unloaded and CO₂ cylinders are removed before cleaning or maintenance. Cleaning. Lubrication. Quick Reference

&#x26A0;&#xFE0F; Always ensure the rifle is unloaded and CO&#x2082; cylinders are removed before cleaning or maintenance.Cleaning<ul data-start="360" data-end="1441"><li style="font-size: 12px; line-height: 1;">Keep the exterior surfaces clean and dry with a microfiber cloth.</li><li style="font-size: 12px; line-height: 1;">Do not use abrasives, waxes, or household cleaners &#x2014; these may damage the plated receiver.</li><li style="font-size: 12px;">Lightly oil the outer barrel shroud with a product like Ballistol or Rem Oil.<ul style="font-size: initial;"><li style="font-size: 12px; line-height: 1;">Apply only a very light film &#x2014; do not leave the surface greasy.</li></ul></li><li style="font-size: 12px;">To clean the barrel:<ol style="font-size: initial;"><li style="font-size: 12px; line-height: 1;">Remove shells and CO&#x2082; cylinders.</li><li style="font-size: 12px; line-height: 1;">Open the lever and keep it open.</li><li style="font-size: 12px; line-height: 1;">Use a patch puller or a soft brass/aluminum cleaning rod with patches.</li><li style="font-size: 12px;">For very dirty barrels:<ul style="font-size: initial;"><li style="font-size: 12px; line-height: 1;">Use a patch moistened with Ballistol or Rem Oil.</li><li style="font-size: 12px; line-height: 1;">Follow with several dry patches.</li></ul></li><li style="font-size: 12px; line-height: 1;">For extremely dirty barrels, follow the barrel change video to remove the barrel and clean separately.</li></ol></li><li style="font-size: 12px; line-height: 1;">Long-term storage: Run a lightly oiled patch through the barrel. Before resuming use, run 2&#x2013;3 dry patches to clear.</li><li style="font-size: 12px; line-height: 1;">Tip: Clean the barrel once when brand new, then only if accuracy declines or if you prefer a freshly cleaned barrel. After cleaning, accuracy may take a few shots to settle in.</li></ul>Lubrication<ul data-start="1466" data-end="1982"><li style="line-height: 1; font-size: 12px;">CO&#x2082; Cylinders: Place one drop of 100% silicone oil on the tip of each cylinder before installation.</li><li style="line-height: 1; font-size: 12px;">Hammer &amp; Lever: Every ~500 shots, apply a drop of silicone oil to the hammer and lever pivot points. Wipe away excess.</li><li style="font-size: 12px;">Pump Models:<ul style="font-size: initial;"><li style="line-height: 1; font-size: 12px;">Apply 1&#x2013;2 drops of non-detergent motor oil (30wt) or air tool oil to the pump pivot points and the foam wiper.</li><li style="line-height: 1; font-size: 12px;">Wipe excess oil across the pump linkage and pump tube to prevent rust.</li><li style="line-height: 1; font-size: 12px;">Do not over-oil &#x2014; a thin film is enough.</li></ul></li></ul>Quick Reference<ul data-start="2011" data-end="2394"><li data-start="2011" data-end="2072" style="line-height: 1; font-size: 12px;">Exterior care: Dry cloth; light oil on barrel shroud.</li><li data-start="2073" data-end="2137" style="line-height: 1; font-size: 12px;">Barrel cleaning: Patch puller or rod; oil + dry patches.</li><li data-start="2138" data-end="2205" style="line-height: 1; font-size: 12px;">CO&#x2082; lubrication: Drop of silicone oil on each cylinder tip.</li><li data-start="2206" data-end="2296" style="line-height: 1; font-size: 12px;">Moving parts: Light oil on hammer, lever, and (for pump models) pump pivots/wiper.</li><li data-start="2297" data-end="2394" style="line-height: 1; font-size: 12px;">Storage: Store clean, with a light oil film on the barrel if not in use for long periods.</li></ul>

1866 CO2 Cleaning & Maintenance

Our customer service team is here to help with any questions you may have!

Have questions? Our customer service team is here to help! We'll get back to you as soon as possible.

Availability
Monday – Friday, 9 AM – 5 PM CST
Closed weekends 
Closed holidays (Dec 24, 25, 26, 31 & Jan 1)

Recommended Maintenance

Break Barrel Cleaning & Lubrication Guide

400e Cleaning, Lubrication & Battery Care

PCP Rifle Cleaning & Maintenance

1866 CO2 Cleaning & Maintenance